Cat6 Network Wiring in Los Angeles: Cost & Guide (2026)
Short answer: one professionally installed Cat6 Ethernet drop (cable, jack, wall plate, testing and labor) usually costs about $125 to $300, according to national cost guides such as Fixr and Monoprice. In Los Angeles, plan for the upper half of that range in a finished two-story home. A single-story house with open attic access is closer to the lower half.
The cable is cheap, about $120 for a 1,000-foot box of Cat6. Labor is most of the price. For homes we install Cat6. For offices, long runs and high-power PoE devices we install Cat6a. Low-voltage network wiring in an existing LA home usually does not need a building permit.
In this guide
What a Cat6 network drop costs
A "drop" is one cable from your network closet or switch to one jack in a room, terminated and tested at both ends. National cost guides put a professionally installed Cat6 drop at roughly $125 to $300 (Fixr, Monoprice). The price per drop usually goes down as you add more drops to the same job, because the setup, the patch panel and the trips into the attic are shared.
Here is what goes into one drop, using our 2026 material costs and our $125 per hour labor rate:
| Item | Typical cost | Notes |
|---|---|---|
| Cat6 riser cable | about $12 per 100 ft | $120 per 1,000-ft box, solid copper |
| Cat6 plenum cable | about $20 per 100 ft | $200 per box; needed in air-handling spaces |
| Cat6 keystone jack | $3–$5 each | One at the wall plate, one at the patch panel |
| Terminations | about 15 minutes per end | Two ends per drop, plus labeling |
| Pulling and fishing the cable | varies most | Open attic: fast. Finished walls, two stories, stucco: slow |
The cable and jacks for a typical 50–100 ft drop cost less than $25. The rest is time. These are the things that make a drop take longer:
- Finished walls and ceilings. Fishing cable through closed drywall takes much longer than stapling it in an open attic. New construction is the cheapest time to wire.
- Two-story homes. Getting from the first floor to the second usually means finding a chase, a closet stack or a path through the garage.
- Slab foundations. Many San Fernando Valley homes sit on slab, so there is no crawl space to run cable under the floor. Runs go through the attic and down the walls.
- Exterior runs. Outdoor-rated cable costs about two to two and a half times as much as indoor cable, and exposed runs usually need conduit.
- Plenum spaces. Commercial drop ceilings that carry return air require plenum cable, which costs about 60–80% more than riser cable.
Cat6 vs. Cat6a vs. Cat5e
| Cable | Speed | Bandwidth | Cable cost (1,000 ft) | Where we use it |
|---|---|---|---|---|
| Cat5e | 1 Gbps | 100 MHz | $80–$100 | Not for new installs |
| Cat6 | 1 Gbps; 10 Gbps up to 55 m (~180 ft) | 250 MHz | $120–$150 | Most homes |
| Cat6a | 10 Gbps up to 100 m | 500 MHz | $180–$220 | Offices, long runs, high-power PoE |
Cat6 is the right choice for most homes. It costs only slightly more than Cat5e and supports 10 Gbps on the shorter runs typical inside a house. We use it on about 95% of residential projects.
Cat6a makes sense in commercial buildings, on runs longer than about 200 feet, near sources of electrical interference, and for PoE++ devices that draw 60 W or more, such as some PTZ cameras.
Whatever the category, insist on solid copper cable. Avoid copper-clad aluminum (CCA) cable sold online as "Cat6": it does not meet the Cat6 standard and handles PoE poorly.
Riser, plenum and outdoor cable
- Riser (CMR): the standard for homes, inside walls and between floors.
- Plenum (CMP): required in air-handling spaces, such as drop ceilings used as HVAC return air. This is common in offices and retail spaces.
- Outdoor (CMX) and direct burial: UV- and water-resistant jackets for camera runs on the outside of a house, or underground to a pool house, ADU or gate. Exposed runs go in conduit.
How many network drops does a home need?
Start from what should be wired rather than counting rooms. WiFi is fine for phones and laptops. Wire anything that sits still and needs a steady connection:
- WiFi access points: 1–2 for a 1,500–2,500 sq ft home, 2–3 for 2,500–4,000 sq ft, 3–4 for larger homes. Ceiling access points powered by PoE give much better coverage than one router in a closet.
- TVs and streaming boxes, especially the main living room and the home theater.
- Home office desks: one or two jacks per desk.
- Security cameras: one Cat6 run per PoE camera (see our camera installation cost guide).
- Gaming consoles and anything that needs low latency.
All runs come back to one place, usually a closet, the garage or a small wall-mounted rack, with a patch panel and a PoE switch. If you are renovating or building, pull one or two spare cables to the places where you will most likely want more later. Pulling an extra cable during the job costs far less than coming back.
The 328-foot limit and when to use fiber
Ethernet over copper, including Cat5e, Cat6 and Cat6a, is limited to 100 meters (328 feet) per channel: up to 90 m of permanent cable in the wall plus up to 10 m of patch cords. That includes PoE. Beyond that you need a switch in the middle or fiber. Inside a house you rarely hit the limit. On large lots it shows up when you connect a detached garage, a guest house, a barn or a gate far from the house. For those runs, or between buildings, fiber is the better choice. We install pre-terminated fiber and bring in a fiber specialist when splicing is needed.
How a professional install is done
- Walkthrough and plan. We mark every jack and access point, pick the rack location, and check the attic and wall paths.
- Pull the cable. We keep data cable at least 6 inches from electrical wiring, avoid sharp bends, and leave a service loop at each end.
- Terminate. Keystone jacks at the wall plates, a patch panel at the rack, T568B pinout on both ends.
- Label both ends. Every cable is labeled at the jack and at the patch panel, so the next person knows where each port goes.
- Test. Every run is tested with a cable qualifier that checks wire map, length and gigabit or 10-gigabit capability, not just a continuity light. For commercial contracts that require full TIA certification reports, we rent a certification tester or bring in a testing partner.
- Seal and patch. Exterior penetrations are sealed, and fire-rated walls get approved fire-stop.
Los Angeles rules: permits, HOA, earthquakes
Permits
In an existing home, low-voltage network cabling generally does not need a building permit. New electrical circuits, structural changes and many commercial projects do. Requirements vary by city (Los Angeles, Burbank, Calabasas and others each have their own building department), so confirm with LADBS or your city. Our permit guide explains how LA treats low-voltage work.
Who can do the work
In California, network and other low-voltage systems work falls under the CSLB C-7 Low Voltage Systems classification. You can look up any contractor's license on the CSLB website.
HOA and condos
Many Valley HOAs and condo buildings restrict visible conduit and exterior work. If any cable will be visible outside, get written approval first. We provide a plan with photos and conduit painted to match.
Earthquakes and heat
Racks and switches should be secured so they cannot tip over, and exterior conduit gets flexible connections at the equipment. Attic work in the Valley is done early in the morning in summer, when attic heat is lowest.
DIY vs. professional
If you have an open attic, a single-story house and a few runs, DIY is possible: a box of solid-copper Cat6, keystone jacks, a punch-down tool and a tester. The hard parts are fishing walls without damaging them, getting the cable path right on two-story homes, and testing properly. Bad terminations often show up later as a port stuck at 100 Mbps or a PoE camera that keeps rebooting. A professional install includes the plan, labeling, testing and a rack that someone else can understand. Sibernets offers a lifetime warranty on installation work.
Get a price for your network wiring
Sibernets wires homes and offices in Encino, Sherman Oaks, Studio City, Tarzana, Woodland Hills, Calabasas, Van Nuys, Burbank and the rest of the San Fernando Valley and West LA. We install UniFi and TP-Link Omada networks on the same visit. The on-site estimate is free.
Frequently asked questions
How much does it cost to run an Ethernet cable in a house?
National cost guides put one professionally installed Cat6 drop at roughly $125 to $300, including cable, jacks, testing and labor. Single-story homes with open attic access are at the lower end. Finished walls, two stories and exterior runs push it higher. The price per drop is usually lower when several runs are installed on one visit.
Should I install Cat6 or Cat6a in my home?
Cat6 is right for most homes. It supports 1 Gbps on any run up to 100 meters and 10 Gbps on runs up to about 55 meters, which covers most houses. Choose Cat6a for long runs over about 200 feet, offices, or PoE devices that draw 60 W or more.
Is Cat5e good enough?
For new wiring, no. Cat6 costs only a little more per box and has more headroom. Existing Cat5e that tests well can stay in service for gigabit internet.
Do I need a permit to run network cable in Los Angeles?
In an existing home, low-voltage network cabling generally does not need a building permit. New electrical circuits, structural work and many commercial projects do. Confirm with LADBS or your city's building department.
How long can an Ethernet cable run be?
100 meters (328 feet) per channel for Cat5e, Cat6 and Cat6a, including patch cords and PoE. For longer distances, such as a detached building, use fiber or add a switch along the way.
How many Ethernet drops does a house need?
Wire every WiFi access point, the main TVs, home office desks, PoE security cameras and gaming consoles. A typical 2,500–4,000 sq ft home has 2–3 ceiling access points. Add one or two spare cables to likely spots while the walls are open.
Can you wire a finished house without opening walls?
Usually yes. Most runs go through the attic and down interior walls with only a small hole at each jack. Where a wall cannot be fished, surface raceway painted to match is an alternative.